国产精品精品国产一区二区,久久久之久亚州精品露出,国产精品久久国产亚洲av,99国产精品99久久久久久

當前位置:首頁-新聞資訊

電烙鐵焊接鋁件的方法有哪些?

來源:http://m.ijizz.cn/ 發布時間:2022-01-07

其一、在鋁件焊接處先涂上焊藥,然后將燒熱的烙鐵蘸飽錫后放在焊處進行預熱,待溫度升高,焊藥由稠變稀后再加一些焊藥和焊錫,使焊錫將烙鐵頭包容起來,然后用烙鐵頭在焊接處前后摩擦,摩擦距離不要過大,一般在3~5mm之間使烙鐵頭處劃破鋁制元件表面的氧化鋁膜。焊接處由于有熔錫覆蓋與空氣隔絕不可能產生新的氧化膜而錫則能及時沾到剛剛除去的氧化膜的鋁件上。等列熔錫由圓球狀變成扁平狀,表明鋁件已經與錫結合牢固,這時就停止摩擦并趁熱擦去剩余的焊藥,再與預先蘸好錫的導線頭或其它元件進行焊接就很方便了。
First, apply solder on the welding place of aluminum parts, then dip the hot soldering iron into tin and put it on the welding place for preheating. When the temperature rises and the solder turns from thick to thin, add some solder and solder to make the solder contain the soldering iron head, and then rub the soldering iron head before and after the welding place. The friction distance should not be too large, Generally, the aluminum oxide film on the surface of aluminum components is scratched at the soldering iron head between 3 ~ 5mm. Because the welding joint is covered with molten tin and separated from the air, it is impossible to produce a new oxide film, and tin can be stained on the aluminum parts with the oxide film just removed in time. The equal row of molten tin changes from ball shape to flat shape, indicating that the aluminum parts have been firmly combined with tin. At this time, it is very convenient to stop friction and wipe off the remaining flux while hot, and then weld with the conductor head or other components dipped in tin in advance.
其二、在鋁制元件的焊接處滴幾滴稀鹽酸用以除去表面氧化膜,稍待片刻,再加入幾滴較濃的硫酸銅溶液,等到焊處全部有銅覆蓋時,用水洗掉多余的硫酸銅溶液和鹽酸溶液,然后用45-75W烙鐵就可以進行焊接,其效果不錯。
Second, first drop a few drops of dilute hydrochloric acid at the welding position of aluminum components to remove the surface oxide film. Wait a moment, and then add a few drops of concentrated copper sulfate solution. When all the welding positions are covered with copper, wash off the excess copper sulfate solution and hydrochloric acid solution with water, and then weld with 45-75w soldering iron. The effect is good.
其三、取一塊鋁放入坩堝內加溫熔化,再加入2~5倍的錫熔化后待用,再按常規方法焊接十分方便。
Third, take a piece of aluminum and put it into the crucible for heating and melting, then add 2 ~ 5 times of tin for melting, and then wait for use. It is very convenient to weld according to the conventional method.
其四、在處理干凈的鋁表面,涂上一層溶液,用100w烙鐵頭上多吃錫,用烙鐵頭在焊接面上邊摩擦邊涂溶液即可。這便可以牢固的焊上。但注意:汞有毒,要在通風處焊接,且不要用劇毒的氯化汞。
Fourth, apply a layer of solution on the cleaned aluminum surface, eat more tin on the 100W soldering iron head, and apply the solution while rubbing on the welding surface with the soldering iron head. This can be firmly welded. But note: Mercury is toxic. Welding should be carried out in a ventilated place, and do not use highly toxic mercuric chloride.

鋁板生產廠家
其五、鋁件土法焊接,預先準備好鋸玻璃纖維板的白粉沫,放在焊處表面,用75w烙鐵在焊接面上用力摩擦直至在鋁表面上附上一層錫,然后再用布將白粉沫和松香的混合物清除掉,這時就可用一般的方法焊接了,經實踐此法簡單,焊接效果令人滿意。
Fifth, aluminum parts are welded by native method. Prepare the white powder of sawing fiberglass board in advance, put it on the welding surface, rub it on the welding surface with 75W soldering iron until a layer of tin is attached to the aluminum surface, and then remove the mixture of white powder and rosin with cloth. At this time, it can be welded by the same method. After practice, this method is simple and the welding effect is satisfactory.
也可取松香、鐵屑混合,再用砂紙打光鋁件面,把松香和鐵粉放在焊接處光面上,用烙鐵反復摩擦使鋁表面吃上一層錫,然后再按一般方法即可順利焊接。
It is also advisable to mix rosin and iron filings, polish the aluminum surface with sandpaper, put rosin and iron powder on the smooth surface of the welding place, rub repeatedly with a soldering iron to make the aluminum surface eat a layer of tin, and then weld smoothly according to the general method.
后方法之六、先將鋁件的焊接處表面打磨光亮,再滴幾滴縫紉機油,油量要充足,然后用鋒利小刀在焊接處來回刮幾次,再用烙鐵蘸上焊錫和松香在焊接處來回摩擦,錫很快就會牢固地附著在鋁件上,此法也較簡單、實用。
The sixth method is to polish the surface of the welding part of the aluminum part first, and then drop a few drops of sewing oil. The amount of oil should be sufficient. Then scrape it back and forth at the welding part with a sharp knife, and then rub it back and forth with a soldering iron dipped in solder and rosin at the welding part. The tin will soon be firmly attached to the aluminum part. This method is also simple and practical.

黄网官方在线观看| 九九在线视频热线视频精选| 日本一区二区三区高潮喷吹| 这里只有久久精品| 中文字幕国产精品一区二区三区| 日本潘金莲三级bd高清| 日韩午夜精品中文字幕| 一区二区三区亚洲av| 我最爱操女人的骚逼| 无码视频在线观看| 日韩毛片一区视频免费在线观看| 午夜性福福利视频一区二区三区| 天天天天天干夜夜夜夜夜操| 插我舔内射18免费视频| 一区二中文字幕在线看国产一区| 操逼啊 啊 啊黄色视频| 99热这里只有精品97| 国产熟女露脸普通话对白| 欧美久久精品免费看C片| 国产一区二区三区 韩国女主播| 午夜精品在线视频| 美女露胸露逼逼自慰| 成人精品视频区一区二区三| 日本高清一区二区三区不卡| 中文字幕欧美中日韩精品| 国产一区二区三区 韩国女主播| 猛插女人小穴视频| 日本一区二区高清免费不卡| 大粗鳮巴r教师人妻91| 人妻夜夜添夜夜无码AV| 99国产精品一区二区| 国产成人精品久久久成人| 最新国产亚洲亚洲精品A| 国产又粗又猛又色又免费| 丝袜片一区二区三区四区五区| 看看美日韩操逼吧| 大鸡巴抽插小穴色虐视频| 精品一区二区av天堂色偷偷| 大肉棒插了按摩视频| 精品人妻少妇一区二区三区不卡| 女人操女人大逼大片|